Back to: Gamme 2012 et + : Série EX

EX-332.2 Integrated hi-fi amplifier 2x100W - Wireless

Print
The Stereo Integrated Amplifier EX-332.2 was designed based on the EX-322 and enjoys many improvements from the EX-362D. These two models have been repeatedly rewarded by the hi-fi press.

Finishes:
noimage
Description
Datasheet Manual Press

 

 

Haute-fidélité French Hi-Fi magazine awarded in November 2017 the EX332-2 by a "Best Buy" Award. Read the French article in PDF.

 

The Stereo Integrated Amplifier EX-332.2 was designed based on the EX-322 and enjoys many improvements from the EX-362D. These two models have been repeatedly rewarded by the hi-fi press.

L’EX-322.2 delivers 2x 100W RMS and 1x 280W into 8 Ohms thanks to its high-performance (500VA Toroidal transformers).

The EX-332.2 incorporates a WIRELESS receiver that allows listening to music from your tablets & smartphones.

 

 
HIGHLIGHTS
- Wireless
- Pre-ampl. Phono disengageable
- Mode stéréo/mono
- AV Bypass
- Power output for optional card
- High quality manufacturing

 

SPECIFICATIONS

Pre amplifier section
Input XLR lines (LINE 1 and LINE 2)
Sensitivity: 600 mV / Impedance: 100k Ohms

Input RCA lines (LINE1, 2 and 3)
Sensitivity: 600 mV / Impedance: 100k Ohms

Amplification section
Output power: 2x100W and 1x280W at 8Ω and 2x160W and 1x130 at 4Ω Harmonic
Distortion: (1kHz, 1W, 8Ω): 0.5% Signal to noise ratio ≥ 95dBA
Frequency response: 20Hz-75kHz
Input impedance: 47 kΩ
Output Impedance: 4-8Ω

Phono input
Harmonic Distortion: (1kHz, 1W, 8Ω): <0.003%
Frequency response: 10Hz-60kHz
Impedance: 47 kΩ / gain: 45dB

 

Connectors
2x XLR stereo line inputs (LINE 1 and 2)
2x RCA stereo line inputs (LINE 1 and 2)
1x Phono input disengageable (or LINE 3)
1x Optical and coaxial input (DAT)
1x Input for optional card
1x Stereo output Pre-out RCA and XLR
2x Subwoofer output
1x Trigger output (Jack mono 3,5mm)
1x Headphone output on the front (6,35mm)
1x Wireless antenna
1x Phase tester (BNC)
1x Detachable power cord
4x Speaker terminals screw-compatible with banana plugs and fork


Dimensions (WxHxD): 430x135x400 mm
Weight: 18.7 kg

Finishes:

 


 

FUNCTIONS
The front panel of the EX-332.2 has touch buttons lighting up a soft white when on. Thus, the amplifier offers a choice of four stereo inputs (including the Optional input). Pressing the corresponding button activates a relay switch sources, unless one prefers to use the supplied remote. Line 1 input uses balanced XLR connectors.
 


The DAC button actives a digital input on the back of the amplifier button. It allows listening to the digital source connected to the amplifier through the integrated digital-to-analog converter. You can leave connect two sources (one on Optical input, and the other on the Coaxial input) and activate the one suits you the best by pressing the DAC button.
 

The GAIN control allows you to lower the overall gain (-10dB) for all of your sources. This allows you to adjust the fineness of the volume control depending on the sensitivity of your speakers and your listening level.
 

The volume adjustment is provided by a network of resistors and non-inductive accurately switched by relay of high quality. This device provides a highly accurate adjustment and perfectly neutral for the audio signal gain.
 

The EX-332.2 has an integrated digital audio converter. This module, with Cirrus Logic CS8416 digital interface and a Burr Brown PCM1793 converter configured to 48 kHz at 24 bits, has two inputs: One S / PDIF coaxial and optical Toslink connector on EIAJ. When selecting the DAC front panel or via the remote control, the button circle of white, indicating selection of the S / PDIF. A second press of the button illuminates its periphery in red to signal the switching of the optical input on EIAJ Toslink connector.

To improve the flexibility of the EX-332.2, it provides a line level output, from the preamplifier section, intoRCA (unbalanced) and XLR (balanced) formats. This feature allows the addition of a power amplifier to perform a bi-amplification.


Finally the EX-332.2 has a phase tester to optimize the "wiring direction" of connecting the power cord. It allows detecting the correct phasing of the power supply and reducing the leakage current at the minimum.

 

 

33230
EX332.2-front-Black-1000x1000web20
EX332-2-black-rear-1000x1000web69
EX332.2-side-black-1000x1000web
EX332.2-front-silver-1000x1000web
EX332.2-side-silver-1000x1000web
EX332-2-Silver-Rear-1000x1000web83
Telecommande-RC-EX2-v2-1000x1000web